This is the command set for the KPC 9612 as described by the help menu.
| COMMAND | PARAMTERS | DESCRIPTION |
|---|---|---|
| ABAUD | RS232 terminal baud rate | |
| ANALOG | Displays analog inputs | |
| AUTOLF | LF sent to terminal after CR | |
| AX25L2V2 | If on, AX25 version 2 protocol used | |
| AXDELAY | Time added to TXDELAY for repeaters (10 msec) | |
| AXHANG | Hang time of repeater to inhibit AXDELAY (10 msec) | |
| BEACON | [{EVERY | AFTER}] | time (1 min) |
| BKONDEL | If on, DELETE will backspace; else \ | |
| BLT | n EVERY|AFTER hh:mm:ss [START hh:mm:ss] | |
| BP96 | If on, 9600 BT is .3; else BT is .5 | |
| BREAK | If on, a modem break will cause return to command mode | |
| BTEXT | Text sent to BEACON in UI packet | |
| BUDLIST | [ON|OFF] [NONE | {+|-}call | call,call,...] | where call={callsign | {<|>}callsign | callsign{>|<>}callsign} If on, only these stations are monitored |
| CONNECT | callsign [via calls] | can be used to reconnect with different path |
| CANLINE | Char used to cancel a partial line | |
| CANPAC | Toggle char used to send output from TNC to bit bucket | |
| CALIBRAT | immediate command to enter calibration mode | |
| CD | {INTERNAL | EXTERNAL | SOFTWARE} | carrier detect |
| CHECK | No activity time before protocol checks on link (10 sec) | |
| CMDTIME | Timing spec to get out of transparent mode (sec) | |
| CMSG | {ON | OFF | DISC | PBBS} | |
| COMMAND | Char used to return to command mode | |
| CONLIST | [ON|OFF] [NONE | {+|-}callsign | callsign,callsign,..] | If on, only responds to stations in list |
| CONMODE | {CONVERS | TRANS} | |
| CONOK | Enables connections to MYCALL | |
| CONPERM | Forces connection on present stream to be permanent | |
| CONVERS | Enter conversational mode | |
| CPACTIME | Enables PACTIME use in conversational mode | |
| CR | SENDPAC char appended to packets formed by SENDPAC | |
| CRSUP | If on, removes every other consecutive CR received | |
| CSTAMP | Time stamp connects and disconnects | |
| CTEXT | Text sent first to someone else connecting to MYCALL | |
| CTRL | {A|B} {OFF | ON | LONG | n} | controls digital output lines |
| CWID | [{EVERY | AFTER}] | time (1 min) |
| CWIDTEXT | Text sent during CW IDs | |
| DISCONNE | Disconnect current stream | |
| DAYTIME | yymmddhhmm[ss] | |
| DAYTWEAK | Fine tune software 24hr clk | |
| DAYSTR | time format | |
| DAMA | DAMA Slave protocol used when on and connected to DAMA Master | |
| DAMACHCK | No activity time before protocol checks on DAMA link (10 sec) | |
| DBLDISC | Forces a true disconnect sequence after DISC while awaiting connect | |
| DELETE | Char used to delete last char in line | |
| DIGIPEAT | Allows digipeating through MYCALL | |
| DISPLAY | {ASYNC | CHAR | GPS | ID | LINK | MONITOR | PBBS | PAGE | TIMING} | |
| DWAIT | Time to allow digipeaters first access to channel (10 msec) | |
| ECHO | Characters from terminal are echoed back | |
| EQUALIZE | 9600 BAUD EQUALIZATION | |
| ESCAPE | If on, received ESCAPE characters printed as $ | |
| FLOW | TNC will not send data to terminal until input line complete | |
| FILTER | If on, removes most control codes from received packets | |
| FRACK | Time to wait for ack to packets (FRACK*(2*d+1) sec) | |
| FULLDUP | {OFF | LOOPBACK | ON} | Allows transmitting while receiving |
| GPSHEAD | n | string |
| GPSINIT | Initial text sent to terminal in GPS mode | |
| HELP | command[*] | prints help message |
| HBAUD | {300 | 400 | 600 | 1200 | 4800 | 9600 | 19200} | radio baud rate |
| HEADERLN | If on, prints a CR between monitored header and data | |
| HID | Auto ID every 9.5 min if TNC is digipeating or PBBS or KA-Node used | |
| HTEXT | Hierarchical address information | |
| ID | Forces an ID packet | |
| INTFACE | {TERMINAL | NEWUSER | BBS | GPS | HOST | KISS | XKISS | MODEM} | |
| K | Same as CONVERS | |
| KNTIMER | KA-Node idle timer | |
| KNXCON | Allows the Xconnect command in KA-Node | |
| LCOK | If on, allows lower case characters to be sent to terminal | |
| LFADD | LF char added to each CR char sent in packet | |
| LFSUP | If on, received LFs are not printed | |
| LLIST | [ON|OFF] [NONE | {+|-}callsign | callsign,callsign,..] | If on, stations listed are completely ignored |
| LT | n text WILL SET LTn TEXT | |
| LTP | n path SETS PATH FOR UI TRANSMISSION OF LTn | |
| LTRACK | n [LT1] [LT2] [LT3] [LT4] [SYSOP] [TIME] | |
| MONITOR | Master switch for monitoring packets | |
| MALL | If on, allows monitoring of connected data between other stations | |
| MAXFRAME | Maximum number of unacknowledged I frames outstanding | |
| MAXUSERS | Maximum number of connections allowed | |
| MBEACON | If on, monitors packets addressed to BEACON and ID | |
| MCON | If on, allows monitoring to continue while connected | |
| MCOM | If on, monitors SABM ( |
|
| MHEARD | [LONG|SHORT|CLEAR] | Display list of stations heard |
| MHEADER | If on, headers are printed for monitored packets | |
| MRESP | If on, monitors RR, RNR, REJ frames | |
| MRPT | If on, digipeater paths are displayed in header | |
| MSTAMP | If on, monitored packets are time stamped | |
| MXMIT | If on, transmitted packets are monitored | |
| MYCALL | This station's callsign {call[-n]} | |
| MYALIAS | Allows digipeating with alias callsign | |
| MYDROP | KISS port address | |
| MYGATE | Allows cross port digipeating with gate callsign | |
| MYNODE | Callsign used for KA-Node | |
| MYPBBS | Callsign used for access to personal mail box | |
| MYPAGE | Callsign allows access to pager | |
| MYREMOTE | Callsign allows access to remote control | |
| NDHEARD | [LONG|SHORT|CLEAR] | Display list of NODES heard |
| NDWILD | Allows connection to any ssid of MYNODE | |
| NEWMODE | If on, returns to command mode when DISC received on current stream | |
| NOMODE | If on, does not automatically change modes between CONV, TRANS, or CMD | |
| NTEXT | Text sent to someone connecting to KA-Node | |
| NUMNODES | Number of KA-Node channels | |
| ONERADIO | Both ports used on one radio | |
| PACLEN | Maximum size of data in I frame | |
| PACTIME | [{EVERY | AFTER}] time (.1 sec) | when to form packets in trans mode |
| PAGE | [-A|-N] [-512|-1200|-2400] [| message | |
| PAGECWID | n|ON|OFF | if on, CWID sent after every page, else after n min |
| PAGEDIR | n | {LIST [call|alias|capcode]} | {+|- callsign [alias] [-A|-N] [-512|-1200|-2400] [-P] capcode} | |
| PAGELOG | n | LIST | CLEAR | |
| PAGEMON | ON|OFF|nzza | Enables monitoring of pages and defines type |
| PAGEPRIV | Restricts PAGE SERVER to password access | |
| PAGEPSWD | Text string used for paging authorization | |
| PAGETEXT | Initial message sent to someone connecting to MYPAGE | |
| PAGEXINV | Inverts polarity of transmitted pages | |
| PASS | Char used to pass special characters as data | |
| PASSALL | Allows packets with incorrect CRCs to be processed | |
| PBBS | Amount of memory (1K increments) set aside for PBBS messages | |
| PBFORWRD | [bbscall [vias]] [PORT{1|2}] [{EVERY|AFTER} n] | starts auto forwarding |
| PBHEADER | Saves routing information in messages | |
| PBHOLD | Incoming messages to PBBS are marked HOLD | |
| PBKILLFW | Kill Personal and Traffic msgs after forwarding | |
| PBLIST | [ON|OFF] [NONE | {+|-}callsign | callsign,callsign,..] | If on, PBBS considers list as family |
| PBLO | [{OLD | NEW}] [{FIXED | VARIABLE}] | PBBS listing order |
| PBPERSON | Restricts PBBS messages addressed to MYCALL and MYPBBS | |
| PBREVERS | Accepts messages after AutoForwarding | |
| PERSIST | Probability of transmitting during slot time (0-255) | |
| PHEARD | [CLEAR] | Display list of PBBS users |
| PID | If on, allows monitoring of all packets regardless of PID | |
| PMODE | CMD | CONVERS | TRANS | TNC powers up in this mode |
| PORT | {1|2} | Port assigned on power up |
| PTEXT | Initial text sent when someone connects to PBBS | |
| RESET | Soft reset | |
| REDISPLA | Char used to redisplay partial line | |
| RELINK | Version 2 will try to reconnect after retrying out | |
| RESTORE | DEFAULTS | |
| RETRY | Number of retries before aborting | |
| RING | 3 bells sent to terminal upon incoming connect | |
| RNRTIME | TNC will disconnect after receiving RNRs for specified time (x10 sec) | |
| RPRINT | Sends text to RS232 port | |
| RTEXT | Text string used for remote authorization | |
| STATUS | [LONG] | Show status of streams |
| SCREENL | CR printed if none received after n characters | |
| SENDPAC | Char used to form packets in convers mode | |
| SLOTTIME | Time between successive tries of persistance algorithm (10 msec) | |
| START | Char to restart output from TNC to terminal | |
| STOP | Char to stop output from TNC to terminal | |
| STREAMSW | Char used to change streams | |
| STREAMCA | Show callsigns with stream switch | |
| STREAMEV | Show stream switch with every packet | |
| SUPLIST | [ON|OFF] [NONE | {+|-}call | call,call,...] | where call={callsign | {<|>}callsign | callsign{>|<>}callsign} If on, stations in list are not monitored |
| SWP | Allows fine tuning of SOFTWARE CD | |
| TRANS | Enter transparent mode | |
| TRACE | Display received packets in hex | |
| TRFLOW | If on, allows software flow control in TRANS receive mode | |
| TRIES | Number of retries on current packet | |
| TXDELAY | Time delay between PTT and radio data out (10 msec) | |
| TXFLOW | If on, allows software flow control in TRANS transmit mode | |
| UNPROTO | {call [via calls]} | path for UI data frames |
| USERS | Specifies streams to be used by incoming connects | |
| VERSION | Displays firmware version number | |
| ID | Forces an ID packet | |
| INTFACE | {TERMINAL | NEWUSER | BBS | GPS | HOST | KISS | XKISS | MODEM} | |
| XFLOW | Master switch for software flow control | |
| XKCHKSUM | If on, Extended KISS uses a checksum | |
| XKPOLLED | If on, TNC must be polled in Extended KISS | |
| XMITLVL | Transmit levels (0-502)/(0-255) | |
| XMITOK | If on, allows TNC to key transmitter | |
| XOFF | Char to stop input from terminal to TNC | |
| XON | Char to restart input from terminal to TNC |
Click to go home.
Click HERE to see the my total rig-page.
This page has been created in a text editor by a real programmer.